DIRECTV SWM SL3S Slimline Dish Kit LNB Power Splitter and Dish

　　Detailed Description

　　This is the SWM SL3S Kit. It converts your Slimline non (SWM) Dish to the New (SWM) Dish Technology from DIRECTV. This Kit is designed with an integrated single wire multiswitch (SWM) which allows you to have multiple satellites feeds at Once. This DIRECTV LNB Kit has 1 output for the new Slimline SWM dish from DIRECTV and all necessary components to convert your Slimline dish into a SWM Slimline dish (single wire multiswitch). This LNB is lighter and better looking. The Slimline encompasses three LNBs to receive 101, 110, 119 degree satellite, plus the new Ka satellite (99, 103) for local HD MPEG4 programming.

　　This DIECTV Slimline Dish has a Slim Profile, makes this dish aesthetically pleasing for areas with Home Owners Association

　　The SWM Dish is: 22.5 in. x 32.5 in.

　　The SWM Slimline Kit Includes the Azimuth/Elevation Mount

　　Includes long and short support bracket for stability

　　This DIRECTV Dish is to be used to pick up high definition local channel programming from DIRECTV

　　One outputs carrying satellite signal from all Five satellites in the sky

　　Heavy duty J-Mount with 2" outer diameter mast opening

　　Capable of receiving DIRECTV satellite signals on the Ku band (101, 110, 119) and Ka band (99, 103)

　　LNB arm with LNBS attached extends 23.5" from the dish surface area

　　Including J-mount Mast, Dish Surface, Dish Back Assembly, Arm and Pole Attachment Braces

　　Product Includes:

　　This Slimline SWM Satellite Dish from DIRECTV includes the Slim Profile Dish, Dish Mounts and all hard ware necessary to completethe installation.

　　This kit includes a SWM SL3S LNB "Single Wire Multiswitch" for a Slimline Dish.

　　It comes with its required power supply

　　This SWM kit also comes with the DIRECTV 4 Way Wide Band Switch

　　All hardware necessary to do the conversion.

　　To be used to pick up high definition local channel programming from DIRECTV

　　The SL3S SWM LNB is designed with an built-in 8-channel Multiswitch which allows you to have multiple satellite feeds at once. Coaxial RG6 cable not included.

　　Manufacturers may vary. All components are DIRECTV approved manufacturers.

　　One outputs carrying satellite signal from all 3 satellites in the sky

　　Capable of receiving DIRECTV satellite signals on the Ku band (101, 99, 103)

　　SWM Power Suply

　　The PI-21 Power Inserter is designed for use on the SWiMLine dish.

　　Frequency Range: 2-2150Mhz

　　Can be used for the SWM-8

　　UL Listed

　　Output: 21v/ 1.2A max/ 25.2W max.

　　Input 100~120Vac/ 60Hz/ 0.6A max/ 30W max

　　Insertion loss 1.5db typ.

　　4-way (Green Label) Wide Band Satellite Splitter, One Port DC Path (Indoor/Outdoor)

　　500mA DC passing from any output to input

　　Diode steered protection

　　Grounding port provided

　　High isolation between outputs

　　LNB is A low-noise block converter (LNB, for low-noise block) is the (receiving or downlink) antenna of what is commonly called the parabolic satellite dish commonly used for satellite TV reception. It is functionally equivalent to the dipole antenna used for most other TV reception purposes, although it is actually waveguide based. Whereas the dipole antenna is unable to adapt itself to various polarization planes without being rotated, the LNB can be switched electronically between horizontal and vertical polarization reception. The LNB is usually fixed on or in the satellite dish, for the reasons outlined below. The corresponding component in the uplink transmit link is called a Block upconvert (BUC).

　　Satellites use comparatively high radio frequencies to transmit their signals.